High voltage DC relay apl100a-24hfd

Model: APL100A-24HFD

application scope:

high voltage main circuit, pre charging circuit, slow charging circuit, fast charging circuit, high voltage auxiliary system, etc. of new energy vehicles;High voltage main circuit system of charging pile;Wind power, photovoltaic and other power control systems

product features:

● fully sealed structure, high safety

● coil voltage: 12, 24 and 48V

● small volume, high switching power

● epoxy sealing technology is used to fully seal the product, protecting the coil and contact system from oxidation for a long time

Executive standard: GB/T14048.4-2010

model explanation:

shape and installation dimension:

coil working voltage (applicable to the whole temperature range):

Number	Working voltage	12VDC	24VDC	48VDC
1	Maximum voltage	16VDC	28VDC	52VDC
2	Maximum absorption voltage	9VDC	18VDC	36VDC
3	Minimum release voltage	1.2VDC	2.4VDC	4.8VDC
4	Coil current	461mA	250mA	122mA
5	coil power(20℃)	5.5W	6.0W	6.0W
6	Coil resistance(20℃)±5%Ω	26	96	392

technical parameters:

category	parameter	unit	value
Main contact	Main contact, contact form	/	A set of bridge type normally open (double acting contact)
	Operating voltage range	VDC	12—900
	Maximum short circuit current	A	1250A(1/2次,60Hz)
	Withstand voltage	VAC	≥2500(1mA)
	Insulation resistance under DC 500V	MΩ	≥100
	Standard contact resistance	MΩ	≤5
Auxiliary contact	Auxiliary contact, contact form	/	A set of normally open (SPST-NO)
	Maximum current of auxiliary contacts	A	30VDC 2A: 125VAC 3A
	Minimum current value of laying contact	mA	8v 100mA
	Maximum contact resistance of auxiliary contacts	Ω	30VDC 0.417Ω;125VAC 0.150Ω
lifetime	Load life (30A/ 450V)	times	≥6000
lifetime	Mechanical life	times	2,000.00
And the release of	And the time	ms	≤25
	The maximum value of contact bounce (after pulling only)	ms	≤5
	Release time	ms	≤10
environment	Shock, 11ms,1/2 sine wave, peak, suction	G	≤50
	Peak sinusoidal vibration	G	≤20
	Working temperature	℃	—40—+85
	Operating humidity range	RH%	5—85
	standard weight	(Kg)	≤0.19

product electrical life curveContinuous energizing capacity curve:

precautions for application:

the life end of contactor, that is, the insulation strength between the leading load ends of the insulation meter is lower than 50 megohm when the DC is 500V

(1) do not touch the load terminal when the relay is energized,Beware of electric shock

(2) the load voltage should be cut off when the control circuit and non-metallic materials are subjected to withstand voltage test

(3) avoid installing the product in the place with strong magnetic field (transformer or magnet), or close to the object with thermal radiation

(4) do not touch the main lead-out terminal with foreign matters and oil stains, and the external lead-in wire terminal and the main lead-out terminal are in reliable contact, otherwise the terminal will be heated severely and the connecting cable will be melted

(5) in the action voltage test, do not make the voltage rise slowly, please drive the coil by step power supply

(6) the bolt locking torque of each installation part shall be controlled within the specified range.The locking torque of the nut at the load installation position is 7n. M;In principle, please do not use it when the stud torque of relay installation part is 8-9n. M

(7) it falls outside the relay and is impacted