High voltage DC relay apl100a-24had

Model: apl100a-24had

voltage main circuit, pre charging circuit, slow charging circuit, fast charging circuit and high voltage auxiliary system of new energy vehicles;High voltage main circuit system of charging pile;Wind power, photovoltaic and other power control systems

Product features:

Fully sealed structure with high safety● coil voltage: 12, 24 and 48V Small size and high switching powerEpoxy sealing technology is adopted to fully seal the inside of the product to protect the coil and contact system from oxidation for a long time

Using permanent magnet to blow out arcExecutive standard: GB/T14048.4-2010

Model explanation:

appearance and installation dimensions:

Coil working voltage (suitable for the whole temperature range):

Number	Working voltage	12VDC	24VDC	48VDC
1	Maximum voltage	16VDC	28VDC	52VDC
2	Maximum absorption voltage	9VDC	18VDC	36VDC
3	Minimum release voltage	1.2VDC	2.4VDC	4.8VDC
4	Coil current	461mA	250mA	122mA
5	coil power(20℃)	5.5W	6.0W	6.0W
6	Coil resistance(20℃)±5%Ω	26	96	392

Technical parameters:

category	parameter	unit	value
Main contact	Main contact, contact form	/	A set of bridge type normally open (double acting contact)
	Operating voltage range	VDC	12—900
	Maximum short circuit current	A	1250A(1/2次,60Hz)
	Withstand voltage	VAC	≥2500(1mA)
	Insulation resistance under DC 500V	MΩ	≥100
	Standard contact resistance	MΩ	≤5
Auxiliary contact	Auxiliary contact, contact form	/	A set of normally open (SPST-NO)
	Maximum current of auxiliary contacts	A	30VDC 2A: 125VAC 3A
	Minimum current value of laying contact	mA	8v 100mA
	Maximum contact resistance of auxiliary contacts	Ω	30VDC 0.417Ω;125VAC 0.150Ω
lifetime	Load life (30A/ 450V)	times	≥6000
lifetime	Mechanical life	times	2,000.00
And the release of	And the time	ms	≤25
	The maximum value of contact bounce (after pulling only)	ms	≤5
	Release time	ms	≤10
environment	Shock, 11ms,1/2 sine wave, peak, suction	G	≤50
	Peak sinusoidal vibration	G	≤20
	Working temperature	℃	—40—+85
	Operating humidity range	RH%	5—85
	standard weight	(Kg)	≤0.19

Product electrical life curve, continuous power on capacity curve:

Notes for application:

At the end of contactor life, i.e. when the DC voltage of the insulation meter is 500V, the insulation strength between the leading out load terminals is lower than 50 megohm （1) Do not touch the load terminal when the relay is powered on to avoid electric shock

(2) When the control circuit and non-metallic materials are subjected to withstand voltage test, the load voltage shall be disconnected

(3) Avoid installing the product in a place with strong magnetic field (transformer or magnet) or close to objects with thermal radiation

(4) Dont touch the foreign matters and oil stains on the main lead-out terminal, and the external lead-in wire terminal and the main lead-out terminal are in reliable contact, otherwise the terminal will be heated severely and the connecting cable will be melted

(5) In the action voltage test, do not make the voltage rise slowly, please drive the coil by step power supply

(6) The bolt locking torque of each installation part shall be controlled within the specified range.The locking torque of the nut at the load installation position is 7n. M;The torque of the stud at the relay mounting position is 8-9n. M

（7) In principle, please do not use it when it falls outside the relay and is impacted